Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi,
I am currently designin one of our product with a nRF51822 QFAC included, and I need to store 17k-bytes in a non-volatile memory.
I am writing the firmware using...
HI,
I am reading LIS2DH accelerometer sensor data to nRF51822 MCU and displaying on hyper terminal. The LIS2DH sensor gives output in the
form of digital through SPI or...
Are there plans to create a nRF5x micro that has finer control over the RF power output? I'm currently using an nRF52, and the 4dBm steps are pushing the limits of our intended...
Hi. I'm using PCA10028, SDK10.0.0, S130.
Q1. I want UART to start or stop whenever I want. It's to save current consumption.
There is "uart_init()" for reference, but...
Hey folks,
i need to programm a nRF52 dev. kit to advertise data and receive advertisings sequentially, without connecting any device. It means that i need to advertise...
Hello everyone,
I have inherited a project from my coworker. It uses NRF51822 QFAAH0 , SDK 4.4.2 and S110 5.2.1 . My device is scheduled to: advertise, collect the data...
We are developinga product for a customer they want a secure connection and I'm trying to get my head around a certain aspect of the security:
If we choose to use a private...
The nrf905 has a CD (carrier detect) pin that is pulled high if the nrf905 detects another device communicating on the same channel. This can be used on the MCU for collision...
Hi,
In my application I am using Multiple App timers. Is there a way to prioritise these timers. Are there any draw backs in using multiple timers in "ble app".
Regards...
I want to set the resolvable private address ( RPA ) manually instead of letting softdevice do it. I went through documentation but I am not sure about it. I know that I can...
Hi
I am trying to put nrf52 device to system off mode, and wake up by button press.
If I do not enable the softdevice everything works fine, and button press wakes up...
Hi, I am trying to use the nRF52 to pass IMU information through BLE to a smartphone. We have a custom chip with the nRF52 and LSM9DS1 on the same board. I am able to program...
Hi!
Friday I can load the binary into PCA10040 (blinky example) ands works well. But today I load de binary but not works, nothing happen.
I'm used this example /Nordic...
It seems that I configured LFCLKSRC correctly, and advertising led flashes correctly.
Can I make any troubleshooting codes for Radio or Antenna?
Can I make some codes...
Hello,
Is it possible to erase only first N kB of internal flash memory before reprogramming nRF51 with JLink?
Lets say that I just want to erase first 64 kB of flash...
