Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Dear Nordic Team,
Thanks for support.
I want to know the possible for voice file transfer to over BLE. I am using BR281 audio detection on semiconductor. I want do the...
I'd like to retain a few bytes after a restart from system_off. I know the GPIO state is retained, are there any other registers other than that? It looks like RTC1->CC[0...
I've been struggling for some time to get L2CAP transfer between an NRF51822 and a Linux machine using bluez.
I've successfully created a connection between the central...
Hi,
I want to understand ANT and want to begin development with ANT once I figured out how it works. After reading posts on this forum I found out that not all Softdevice...
Is there an example for using a 10 pin 2 digit 7 segment display similar the picture below?
It is common anode and actually has 10 pins (pin 2 is the DP or decimal point...
Hi,
I was wondering about that I did not found any information about dedicated pin usage.
I am using I2C/SPI and UART and did I understand it correctly that i can use...
My application has two firmwares with different offset addresses. One firmware sitting at 0x16000 and second one is at 0x25000. I want jump to the second application from...
I have an issue where after transmitting a radio package, is setting up the radio as receiver, get indication for reception (have indications for ADRESS and PAYLOAD events...
I programmed my beacons with ble_app_beacon (nordic firmware). android can locate my beacons without any problems.
I installed nrf connect app, it can find them too.
but...
Hello,
I'm using BLE, RTC and app_timer to blink a led.
I blink the led 10 times when I receive an order from BT (by means of NUS), and then by means of RTC.
uint32_t...
Hi. I'm very new to this so I hope you'll forgive me for my basic questions!
I would like to take data from multiple ANT fitness devices and send it to an iPhone application...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and i have chosen mono-pole antenna is a good choice,because...
I Programmed my beacon devices with this firmware:
ble_app_beacon.zip
the only app that can find my beacon on ios is nrf connect. in this firmware the uuid is this:
...
