Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
While reviewing the Thread DFU examples I saw that Nordic ported the IoT CoAP library to thread. Is it possible to use other IoT libraries with some modification? Obviously...
I am creating a BLE peripheral device which I want to test using the automated testing feature of NRF Connect. I have connected a android phone to my windows PC and the phone...
Hi.
I'm trying to send data through L2CAP from Cypress BLE evaluation board to nrf51822 chip.
It seems that Nordic's API for L2CAP is much simpler than Cypress', but I...
I noticed some suggestions to add Static Passkey.
I have 10040 nrf52832 sdk13.0.0 s132
The server has no IO, so cannot enter passkey from it.
Is there an example...
Hello,
I am working on NUS service S110 8.0 softdevice and SDK 9.0 and added DFU feature for the application.
First, I connected to the device using MCP from PC. It...
Hi all,
I'm trying to use the nRF51822 sniffer to troubleshoot my TI CC2650STK sensortag ble communication and the output is slightly confusing. The problem I am having...
I need to do the following when assembling a device with nrf-52 at the factory.
Add firmware onto device
Add a unique serial number for the device
Print a sticker...
i have added pwm into proximity profile example and now i am able to make beep using buzzer with pwm library.Now i want to make some sort of Tune instead of beep.
Can any...
hi,all
i use ble-sniffer_win_1.0.1_1111_Sniffer.exe,but it note as follow:
and Why sometimes not get the connection of the data? Sometimes it stop 60 CONNECT_REQ...
Hi
I use SD310 and nRF51 in SDK10 and The Ant is set HRM_MSG_PERIOD_1Hz.
I integrate a heart rate module by I2C and the heart rate data is only all I got.
But the Cell...
Hello,
while I already managed to solve a couple of problems regarding a proper handling of the DFU procedure in my previous topic here , there are still 3 problems that...
I was wondering what would be a good block size, and saw this in the documentation:
For example, if a module has a table with 10 entries, and each entry is 64 bytes...
Hi Nordic,
I am now trying to use ANT acknowledged data type in reverse direction (from slave to master), and I have some questions:
When sometimes, ack signal...
Hey, I want to save stuff to flash under the same id and key which should be no problem as shown in the documentation. But when I save it and retrieve the data only the last...
