nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Can nRF51422 or nRF51822 can be used as bluetooth device for Raspberry pi?
As I can see on the terminal Linux, the hciconfig log says, raspberry pi 3's Bluetooth device...
Hi,
I recently migrated our code to the SDK 13 (we use the nrf52832) and now the function:
uint32_t err_code = ble_radio_notification_init(6, NRF_RADIO_NOTIFICATION_DISTANCE_5500US...
Hi,
I can't discover more than 5 characteristics on central with SD130 2.0.0.
I have trided nRF Connect and characteristics were discovered successfuly.
Is there some limit...
Hi,
I have a situation as below.
I have the list of host addresses (public type). Based on the command received, BLE peripheral device should advertise in direct advertising...
Hello there,
We are using nRF52832 custom board. I2C and GPIO are working on it. Then I uploaded BLE program (which is tested on nRF52-DK) but BLE is not showing up at...
Hey Guys,
I noticed when I use nrfutil DFU BLE command on the nRF52 DK the nrfutil program a "connectivity firmware" before the perform the DFU BLE to a Target device....
hai
i have tried to store and update some data in flash using pstorage. on storing data data is stored successfully.
#include "mbed.h"
#include "pstorage.h"
#include...
Hi all ,
hi NORDIC team ,
I'm currently developping a multiprotocol adapter LORA/BLE . I'm using the sd130 .
Semtech's third party says that it's "recommended " to have...
52832，SDK12.0.0
I met such a situation:
In the use of JLink burning program or air upgrade, after the completion of the program card died in initialization low-frequency...
If I am programming a BLE Server device, and I configure a characteristic with BLE_GATTS_VLOC_USER and queue a notification with sd_ble_gatts_hvx(), how soon can I update...
We're developing with SDK 10.0, nrf51, softdevice 8.0.0, s110.
We started with the ble_uart_app and added our own functionality, which includes the timeslot functionality...
the code is
nrfjprog -f nrf52 --snr --memwr 0x10001080 --val 0xabcd0102
I am doing the example infocenter.nordicsemi.com/index.jsp
I am able to get everything up to...
Hi,
I am currently going through the GCC and Eclipse tutorial. Now I struggle to compile the project.
I installed the blinky project (nRF5_SDK_11.0.0_blinky_blank_pca10040...
Hi all,
nRF52840 and S140 support bluetooth 5. Bluetooth 5 expands 8.x adv data length. I test it on the ble_app_att_mtu_throughout example and add more 30 bytes data to...
Hi,
I have a question about choosing "correct" soft device. I need only peripheral connection, but I'm bit in doubt for choosing SD110, because compatible sdk ver 10.0...
