I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello everyone,
I would like to learn how to create unit tests using the ZTest framework for a Nordic sample project, in order to better understand how it works.
I am...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Hello,
We have developed a custom board using the nRF9151, with the design and board files largely based on the Thingy91x. We are using the nRF Connect SDK v2.9.0. When...
Hi,
While migrating the SDKs and toolchains from version 2.9.0 to v3.0.0, I encounter these configuration warnings which are blocking my build. Hope someone in this forum...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi, I'd like to evaluate Linux device driver for nRF7002; refer to 315431 , I'd found this requirement had been reported one and half year ago; based on 315431 , I have a...
Hello,
I study the UART Central-Peripheral example (NUS) out of the box based on Visual Code IDE. I would like to understand on the Central part:
Where exactly in code...
Hello,
I have a ble mesh with a nRF52840 Eval board and a certain number of nRF52840 dongle nodes.
I communicate via mesh Chat between the Eval board and the nodes.
...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
Hi Nordic team,
I'm using the nRF9160 DK with nRF Connect SDK v2.9.1, and trying to run the coap_client sample to send a GET request to the public CoAP test server at coap...
I’m curious about the current consumption.
Based on the nRF52840 chipset, I found that the current consumption in both sleep and TX states varies depending on the TX power...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hi Sir
The npm1300 allows setting the default voltage using resistor values as shown in the table below. However, if I want to set the voltage to 1.05 V using resistors...
