I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
Hi! It seems that I may have uploaded a non-working application to the Thingy91x. Therefore Device is not conectable via USB. The device is responding only in "MCUBOOT" mode...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello all, I am writing this as I am very new to Studio visual code, nrf connect, and many various things used in this project. Currently I am using the two samples given...
dear all,
We are fighting with a problem that defied every effort to solve it so far, so we are asking for help. Our custom board is based on the nrf5340 SoC connected via...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
Hello,
I am using nRF5340 DK, I was trying to connect it to my laptop MacBook Pro M2 but I continuously get this notifications about JLink disconnecting and reconnecting...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
This is a product based on nRF52832, which uses BLE Bluetooth to scan iBeacons and communicates with an LTE module via UART for data reporting.
It occasionally enters the...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
