i am writing data from wav file to w25q128jv and i got error -22 at some offset while writing. i tried many config but it seems the problem is not solved, does anyone have...
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I have merged all the 4 file's together (app.hex, app_valid_settings.hex, softdevice.hex and dfu.hex).
Then I uploaded the custom app with dfu services enabled using nrfgo...
Hi there,
I'm porting an app from NRF51 SD130 to NRF52 SD132, both with sdk11. I do the usual stuff, like changing includes, freertos ports libraries, etc, and everything...
Just a general resource question. The Softdevice uses RTC0, FreeRTOS (by coded default) uses RTC1. So in order for the SDK ble_conn_params.c to run properly I have to link...
I was able to add the Device Information service as well as a proprietary service using a 128 bit UUID. I modeled after the ble_peripheral uart example. However when I try...
Nrf52/Kiel/SDK11
My application was at the point where I needed to add DFU. Following the examples and SDK doc, I added the files and code needed. It would NOT advertise...
We recently moved from SDK11 to SDK13. We run out of memory when adding custom services & chars to the S132 v4.0 softdevice. Increasing the app start address in the linker...
For the record I have been struggling with migrating a project from S110 @ nrf51422 to S140 @ nrf52840.
Quite by accident, I found this "nrf51_to_nrf52840.h", what does...
Hi , Everyone!
Now i have the board nrf52832 and i'm conducting my DFU.
My DFU is to update softdevice and application.
Here is detail about my problem:
softdevice...
Hi
From s140_nrf52840_5.0.0-3.alpha_migration-document, it is mentioned that the L2CAP API has been completely removed. Are there plans to re-expose the API? We have exposed...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...
I'm looking for an answer as to how to know the source files that I need to mention in the Makefile if I'm writing my program from scratch. Are there some bare essentials...
Hello,
I am writing here because I am trying to change some concrete values from a .hex file in order to vary some BLE and other values. I need this because I need to generate...
