Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Our BLE hardware is designed to send data at 50 Hz speed continuously using nrf51822.
It worked well with APP with Android 4.3 and some Android 5.0/6.0 ,we can receive data...
Hi,
I'm getting familiar with my nRF52 DK (PCA 10040).
I stumbled on something when I was doing an application that toggles LED1 on every TIMER0 event (200ms). Here...
Hi,
Id like to understand the FDS state after flashing the device. Im trying to check if the record exists then I use it, otherwise I write a valid info into the record....
Hello All
Could you please guide me. i want implement BLE with SPI interface...if i sent any command via mobile Bluetooth..then NRF51 DK should receive the Command and...
I have already changed the define NRF52, NRF52832_XXAA,BOARD_PCA10040 to NRF51,NRF51822 and BOARD_PCA10001 and adjusted the ROM and RAM areas as below.
But there...
ERROR OCCURS WHEN TESTING UART nus service on a nrf52832 custom board UART APP SHOWS LIKE THIS device doesn't support UART WHEN I TRYING TO CONNECT WITH MY DEVICE. PLZZ H...
Hi Nordic Team,
In one of our application, we need to interface BT HCI chip with Host MCU(Cortex M4 based). Below are the application profiles we need support for:
...
I am having trouble using GPIO P0_9 and P0_10 as GPIO pins. These are the pins designated as NFC1 and NFC2.
I am using the following sample code:
#include <stdbool.h...
Can a peripheral device know when the client made a scan response request? I want to use scan response as a form of acknowledgment so the peripheral device knows that the...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
It looks like there is a new version of nRF Sniffer for the nRF52, but it doesn't seem to be formally released, although it seems to be 6 months old. Is it expected to be...
Hi,
i was just wondering as we dont need the high clock rate whether its possible to run the nrf52832 with less than 64 Mhz by replacing the 32 mhz crystal with a different...
A brief description of my system:
I have a HUB gathering data from the nrf52832 through SPI. The hub is the master and the nrf52832 is the slave.
According to the nrf52...
