Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I have nRF52 and working with SDK11.
I can start BLE advertising and nRF Connect app will detect everything correctly.
I only have an issue: I want to advertise for...
Hi there,
I am getting some error in my SAADC measurements and I believe it's due to the R_INPUT forming a parallel resistance with my voltage divider at the input (the...
Hi,
I am measuring the current during sleep, after the sequence, __WFE();__SEV();__WFE();.
With NRF_LOG_ENABLED set to 1, the current is about 486 uA. With NRF_LOG_ENABLED...
Using: nrf51822, SDK 10.
My application needs to use TWI0 and SPIS1 at the same time. However if I enable TWI0 and then SPIS1, when I run nrf_drv_spis_init() I get NRF_ERROR_INVALID_STATE...
I am working with the SDK 13 ble_app_att_mtu_throughput example. With the SDK 12 example, it seems to require the SoftDevice to be loaded with the arm5_no_packs example. The...
Hello,
I'm designing a project with the nRF52832 where I will use an external SPI ADC.
For debug and backward compatibility purposes, I also plan to use the SAADC.
The...
in the ble multilink central example i'm not understanding where the functions in client_handling.c are exercised some don't seem to be used in main or client_handling (client_handling_dm_event_handler...
I am reporting a problem that might bite you. A Waveshare NRF51822 module comes with a "Passed" sticker on the back (solder side) that makes the module stand off the mother...
Hi,
We are trying to have a thin beacon design. But we are having difficulty in finding low profile inductor for dc-dc converter matching the recommended value of 10uH...
I'd like to use Logic Analyzer in uVision 5.2 and ulink2 for analyzing variables in nrf52832.
In my understanding, I need to use SWO and configure Trace setting properly...
Hi,
I need to capture a demodulated, manchester encoded signal (16 bits long). The data rate is about 50kHz (give or take). Currently, I am configuring a PPI with timer1...
Hello,
I'm using nRF52840 which is surpport Bluetooth 5. I couldn't understand why it can do 8 X range and 2 X data rate than Bluetooth 4.2.
Besides, how to use Bluetooth...
I observe strange behavior while reading value for long characteristics.
I have characteristic 100 bytes long (read only).
In GATT client I must read value with subsequent...
