hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello, I use nRF51822 based device with s110 softdevice. I noticed that data exchange is different on different connected centrals.
For test I used Windows and Android powered...
Hello,
I have my project up and running using the "nrf51-micro-esb" project. I can successfully set my device to PRX mode and have it receive payloads just fine. Similarly...
Hi,
I have an issue about power consumption with a board nrf52 10040. The consumption should be 100µA but is 500µA. I found an errata about that in ' infocenter.nordicsemi...
We're using nRF52 to read two sensors data: one is an ADC chip using SPI; the other is a PPG sensor using I2C. MCU sampling rate is 250Hz, meaning every 4ms, MCU will poll...
Hi all!
I'm a beginner developer.
I start my work with nrf51822, download examples e.t.c
Now I try to download my code in real PCB with external 16MHz crystal.
Code worked...
-----------------------------EDIT--------------------------------------
I've changed topic name, because not buffer overwrite is the problem.
I need some mechanism for...
I am working on a project for college in which I need to build my own PCB. The code works fine on the Dev Kit but on the PCB, the bluetooth is not showing. I have tried looking...
Hello,
I am using nRF UART v2.0 android app and I have added my custom logic above it. I am using this phone as the central device and nrf52 with sdk 12 as the peripheral...
hi
i am using two dongles.one would be sending sensor data from gpio to other through ble.i need a example code for those two.could you please tell me which example i can...
Due to limited budget, I have to use STLINK/V2 to flash code into nRF51822. I have been through steps of how to setup OpenOCD/STLINK/V2/nRF51822 in Ubuntu. After mass erase...
Hi. I'm using nRF52832, SDK13, S132v4.0.2.
I'm making peripheral device using nRF52832.
And I can see it gets BLE_GATTS_EVT_WRITE event as below when central sends WRITE...
I'm having a difficult time getting my project to link to the nrf_serial module
._build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_serial_read (referred...
Hi
From my understanding of the softdevice API, the maximum packet length is set using sd_ble_opt_set(BLE_GAP_OPT_EXT_LEN, &opt) , but the actual change to the packet length...
Hello,
I would like to build a sensor array that communicate with one master in a star topology.
I have played with the Gazelle protocol example ( gzll_ack_payload examples...
Hi,
I am working on a project where I have 4 advertising beacons which will have to trigger some functions in the central side when it gets the advertising data.
Now I...
