Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Faced with problem in subject during porting Serialisation to STM32F4 chip.
Serialisation library extensively uses function call triggered by NVIC.
How to substitute this...
I'm using ANSC example, pca10028, iphon5s and iphon4s.
I confirmed #define DEVICE_MANAGER_MAX_BONDS 7.
But pca10028 cannot pair with iphone5s after paired with iphone4s...
Hi,
I'm using nrfutil to update my nRF52832.
I change target from nRF51822 to nRF52832 and I want be able to bootload my target through own master.
In past, I used...
I have followed instructions at the link below to setup a Raspberry Pi 3 as a 6lowPAN router, and am trying to run the dns example from nRF5 IoT SDK 0.9.x on an nRF52-DK:...
Hi,
I'm using pca10040 and prebuild hex with s132 from sdk 12. Now I'm wondering how can I get number of sent data? If I set it as transmitter - send via uart 0x8094 i...
Hi all.
What happends on peripheral side when I use long write by sd_ble_gattc_write as devzone.nordicsemi.com/.../ ?
How Can I read it on peripheral ?
Can I use once...
hello there i want to use low power comparator nrf51. now my device work with battery. so i think i require internal reference. now can you tell me how to use internal reference...
Hello, recently I've found an information about bit counter in Radio Module in nRF52 Product Specification. Unfortunatelly I can't find any reference at infocenter how to...
Is MTU of all BLE devices limitted to 23 bytes when using ATT protocol?
I don't know explicitly.
Some say it is possible to use MTU longer than 23 bytes.
Others say...
I am using TAIYO-YUDEN EYSHCN, which is having Nordic-nRF52832 chip on it. As per document from TAIYO-YUDEN, recommended to flash s132-firmware on it. I downloaded s132_nrf52_3...
I have two questions with the remaining unresolved symbols being the most critical. I will decribed the situation I have encountered as a sequrence of chronological steps...
Hello,
I have a need to construct multiple portable devices on a short time frame. We expect that building Arduino-format shields for our peripherals and using nRF52 DK...
I am using PWM on a BLE Nano using Nordic SDK. I was having problems with the PWM and decided I would set the duty cycle to 0 to see if the program was working right:
#include...
