Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello,
I am trying to compile the example ble_app_eddystone with the SDK12.2 for the nRF52_pca10040_s132
While compiling with SEGGER I get the error
Compiling...
Hello,
I set up a project on the base of "BLE_APP_UART" to which I added header files and configured the sdk_config.h
Now I get these warnings during compilaiton:
...
Hi!
So I went from the Battery Service example to create my own service which went well and everything. Now I don't need a battery service, which is why I was trying to...
Hello,
i am working on Low current consumption project.
i have one question. what will be the good option to use the SPI or TWI ?
who have less current consumption ?
...
Hi, I want to ask some questions about BQ24090.
According to the schematic in the datasheet of BQ24090 , I have several questions below:
When should the led indicator...
I added the peer manager in my SDK11.0.0 application. I also have OTA DFU but everytime I boot into the bootlader, the first connection fails and I have to reconnect again...
Hi,
I am getting the "Couldn't connect Nordic_HRM" toast using the experimental project.
I saw the question but the answer there (sample code for selfie stick) is a very...
If I enable the Data Packet Length Extension and I enable the Connection Event Length Extension, having a connection interval of ~400ms I know that I can reach up to 251 bytes...
Hello,
I am trying to implement a Heart Rate Monitor Interface (HRMI) board with my nRF52, using the TWI_sensor example from SDK 12.2. I am unable to read any heart rate...
I use the S130 stack and enable the service changed feature when enable the soft device. I found the handle can be got when call add API. But this is GATT handle. How can...
UPDATE:02/28/2017
I MAKE A BOARD ,WANT TO KNOW DOES THIS PIC MAKE SENSE?
I WANT USE STM32F072B REPLACE JLINK OB.
STM32 HAS USB I WILL WRITE CODE MAKE A virtual...
Hi,
I download nRF5_SDK_11.0.0_89a8197 and open the SPI example in the peripheral folder using Keil V5.20, but I found that the project cann't be build. Could you tell...
I know the Source code for the MCP is not provided ..
I also Know the the masteremulator dll is available ... and there are several samples code demos available.
but I am...
hello,
In nRF 52, after executing ble_advertising_start after BLE_GAP_EVT_DISCONNECTED, although BLE_GAP_EVT_CONNECTED is set on the device side although the central is disconnected...
