Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
When I call sd_ble_gatts_sys_attr_set and p_sys_attr_data points to data in flash I get a NRF_ERROR_INVALID_DATA. When I point to the same data in RAM I don't get an...
I am using NRF_TIMER1 with 16-bit mode and prescaler of 0 as a counter, to count the pulses of an incoming square wave signal in a given time window. What is the upper limit...
Hi Nordic,
Can you please shed some light on the size of NFC stack on nRF52?
Also, what NFC operation modes (Reader/Writer, Peer-to-Peer, Card Emulation) can be supported...
I'm pretty new to embedded systems development, but I've started to find my way around. I am trying to strip the SDK example programs down to minimal examples, in order to...
Hi!
I am trying to implement oob pairing, but I don't know how to do it.
I' ve got 2 nrf devices. Central and peripheral.
Central receives oob data, which it stores in...
Hello, I am using spi_master example to get a sensor output from ADXL345. Currently, it seems my code can read output data, but there is error showing for settings mismatch...
Hello!
I successfully followed nAN-36 and loaded the code into a NRF51 DK (PCA10028).
The next step I intend to take is to prepare a custom central service that matches...
Why sd_ble_gattc_hv_confirm returns NRF_ERROR_BUSY ?
I want to send a confirmation after I receive a indication from server(s110 ) ,when I receive data ,
in on_evt_hvx(...
I am trying to figure how to pin my nrf51822 on a PCB. I need the chip to sample and convert an analog voltage signal coming from a photodiode heartbeat detection circuit...
Hello
I want to setting up DFU in my project. I followed this document :
link text
I'm using IAR EWARM and nRF51_SDK_8.0.0 and "nRF51_SDK_8.0.0\examples\dfu\bootloader...
Dear all,
I have written some code that controls the SPIS and allows it to transfer data as if it were a master. I am generating the SPIS clock from one timer, and I am...
Hi everyone
for my application I must use the Bluegiga dongle like central (PC side) and nRF51822 for peripheral (hardware side).
So I implemented cable replacement app...
I feel stupid asking this question, it should be documented in the standard and the code but I have looked and googled with no luck.
I want to populate the ble_rscs_meas_t...
