I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
In the nRF8001 Product Specification, section 7.1.5 it states:
"The maximum length of an event packet
is 31 bytes, including the length
byte."
In the headers...
Has anyone seen more than 3 notify packets per 7.5ms connection interval?
I am seeing 3 and am wondering if this is a fault of the way my app is working.
My Setup:
Nordic is the Server, Android is the client.
I have read many, many forum posts about doing long reads/writes. Virtually everyone says you cannot do long writes...
I am trying to connect more then one device to nrf51822 HID.
How can i pair more then one device ?
How can i delete paired device from nrf51822?
Thanks
Recently ran nRF Master Control panel on android and found "Read remote RSSI" button. Is data got from device in some way or simply measured by androd phone ble radio module...
I would like to write to multiple characteristics in a loop but the second call to sd_ble_gattc_write() causes a NRF_ERROR_BUSY error. From reading the documentation, I should...
Hi all,
I am working with PCA10028. I have a peripheral and central both are devices with no display and no keyboard. both peripheral and central device are under our control...
Hi,
I am using nrf51822 with s110 softdevice version 8.0.
Is there any way i can know the state of my radio at some point in the code execution?
In short I want to access...
As explained by electronut in his Blog and Lijun here , it is possible to program an External nRF51822 board using the SWD interface of the nRF51-DK.
But what about a custom...
I have a project, and nRF52832 it 's good chip for me, because it has NFC/ bluetooth communication.
I would like to know if nRF52832 can pilot epaper display. nRF52832 does...
Hi,all. i face a problem. the office DFU flowchart is device reset--->bootloader --->upload firmware to device ---->device reset.i want to implement as follow: upload firmware...
Dear all
We did nordic beacon board in that we not able to flash the device
We are checked core voltage 1.2V and 1.7V are coming .But i want to confirm external CLOCK will...
Hi,
I want to change the interval time of 51822 dongle with the instruction here devzone.nordicsemi.com/.../
The default value is 100ms as following
#define NON_CONNECTABLE_ADV_INTERVAL...
Hey guys,
I’m working on an nRF51822 design where I’d like to check the value of a GPIO at Power-ON, then either shutdown, OR start the BLE stack and do BLE stuff. I really...
when compiling " ble_app_proximity " exampled by Nordic, it indicates errors:
" D:\Program Files\MDK5\ARM\PACK\NordicSemiconductor\nRF_Drivers\3.0.0\gpiote\nrf_drv_gpiote...
