Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I'm wondering why I can't see any packet from example led_mesh in your's sniffer?
Theoretically it's only Nonconnectable Advertisements or I miss some information...
What will be the price of nrf52 chips compared to nrf51?
Will there be any cheaper version of nrf52 chips with limited capacbilities (e.g. less flash, ram)?
I was trying to setup a GNU toolchain on Windows and use the nrfjprog utility, but despite having installed the J-Link drivers (4.78), nRFGo Studio as well as the nRF51 SDK...
I cannot seem to get pstorage working using the S210 softdevice. I can get it to work using the S130. I was not able to find any info on pstorage using S210.
I used the...
Hi
I want to use the nRF51822 to do the BLE product.I have read the datasheet of nRF51822.I have some questions:
1、Can the I/O of nRF51822 support 4.5V~5V input?
...
Hi All,
My goal is to change the advertisement(when not "connected" to ble device) in every SPI Interrupt, depending on the data received i set corresponding data in advertisement...
In porting over my project from Keil to GCC using SDK 8.1.0 I can build and run just fine when I build with Keil but when I build with GCC and try to run sd_softdevice_enable...
Hi,
I trying to write an application with android for my nRF51822 device
I use Battery service example but every time i update battery level i need to request for changed...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,all.i want to run DTM on pca10028 develop board and connect it to my pc via USB (JLink CDC UART Port) on the board.My pc operation system is ubuntu10.4. what is the port...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,all. i run example.py(nAN34 document) on ubuntu10.4,then get an error:
./example.py:line 13:unexcept error near "(";
./example.py:line 13:'def main():'
what's wrong...
Hey there,
I am having issues downloading the SDK for the NRF52. It just goes to a blank part of the page. Is there a better way for me to get a hold of this SDK?
T...
So after reading some material it seems like I can pretty much define which pins are responsible for I2C communication. Is there any limitation to which pins I can set? Does...
Hello,
There are many anomalies in the NRF52 Revision Engineering A (QFAA-AA0, QFAA-AC0) .
This revision it is the current chip?
If so, do you know when there will...
