I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
hi,
im trying to implement a one shot timer and followed the tutorial here:
devzone.nordicsemi.com/.../
note that i adapted the code for a custom project (and a custom...
According to nRF52832 Product Specification v1.3, tPOR is written as follows.
Is the VDD rise time range from 0 V to 1.7 V or from 0 V to 3 V?
Please tell me the range...
Hello,
I'm trying to change advertisement packets, I found this link text
it says:
p_data Raw data to be placed in advertising packet. If NULL, no changes are made...
Hi, I'm trying to change ad packets in the blinky example. I want to be able to keep blinking but change the ad packs (don't know if this make sense, but main goal is to change...
I have created a build system that will install openmesh on simblee chips, and it appears to be mostly working. However, range is very poor, like max 2ft. I have tried adjusting...
Hi guys,
I am working with a central battery powered so, I am controlling the RF activity calling scan_start() or sd_ble_gap_scan_start() and disabling the RF activity...
Hello,
We are switching chips from the nrf51 to the nrf52832. I have a nrf52-DK board now. My Eclipse set up is still able to compile, run, and debug my nrf51 projects...
hi,
im a little lost with BLE at the moment. all i want to do is sending 3 bytes of data (sensor data) approximately 10 times (+- 5) a second (when the uC is not sleeping...
As a central, I am writing to a variable length characteristic, advertised by a service of my peripheral. In this case, I am sending 80 bytes of 0x01 as a test
uint8_t...
I used the ANCS program in sdk12.3.0, I have closed the white list function, I use the iphone connection and paired, then I ignore this device on the phone, and then I use...
Hi
I am using nrf51-dk board along with the S130. I am getting the following message when I debug my code. The central link count is set to 0 while peripheral link count...
Hello,
I didn't find much information about how different settings for the MTU size behaves with older versions of BLE devices. I'm using the softdevice s132 4.0.2.
...
When trying out the ble_app_hrs_freertos example in nRF5 SDK 11.0.0-2.alpha_bc3f6a0 , I seem to only get 14-character long device name announcements.
This happens when...
