Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hey.
I am wondering if there is a way to disconnect a slave from a master based on the strength on the connection and not when they naturally loose connection.
To give...
How do I block Bluetooth signals ? (I want the signals to be transmitted 180 degrees, not 360 degrees)
I have read it could be done with aluminium foil, but I have not...
I am looking at using an nRF51 in a BLE product (industrial applications).
One of the things that I have to sort of prove is that it will be a better choice than something...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
We are looking at using the Gazell protocol for a project. There isn't much information out there except for the "Gazell Link Layer User's Guide"
developer.nordicsemi.com...
Hi,
I've been working with a two LPC1768 boards with connections to Addicore nRF24L01+ boards.
I have not been able to successfully receive an ack on the PTX board although...
Hello
What is a typical current draw when using a PORT GPIOTE interrupt? I seem to be drawing approximately 200uA with a port event enabled. Is this normal?
I'm using...
Here: developer.nordicsemi.com/.../a00050.html
"The Bootloader/DFU with SoftDevice update example shows how a SoftDevice, bootloader, and pplication (sic) can be updated...
Hi,
I am trying to bring up custom board with 51822 CFAC-A0.
And I am continuously getting the following error as soon as the code does advertising_start().
I am using...
This comment for this line of code in twi_sw_master.c is misleading:
#define TWI_DELAY() nrf_delay_us(4) /*!< Time to wait when pin states are changed. For fast-mode the...
