Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Good Moring engineers.
I just got nRF24LE . I am wondering the timer2 only provide 2 seconds long period ?
I want my project nRF24LE sleep as long as possible , at less...
I am using an RTC for other purposes that exposes a buffered 32kHz clock. I am considering using the buffered (rail-to-rail) for also the LF timebase of the nRF51. The drive...
I've just discovered that the Jlink LITE programmer can not program my custom PCB because it runs at 2.7V.
Does the nRF51-DK board support programming an external target...
Hi....
We are working on PCA10028 DK with S130 softdevice version 0.9.0 alpha. Could you tell me about the release of stable SD S130. Hope it will be soon.
Hey,
Is it possible to use the NRF51822 for connectivity together with Arduino, and if so are there any easy instructions as to how to do so? I am looking something on...
Hello I was wondering if I can use both the proprietary protocol 2.4 Ghz ( I understood the one to use for the new projects is Gazell ) and the Blueotooth smart on the nRF51422...
Recently,I met a problem when I used Gazell mode. Before, i used the GPIOTE to collection PPM receiver 's length of time, when I also use the gpiote and wireless data transmitting...
Hello , i have been following the ANCS tutorial and have managed to pair it with my iOS device. I am using the Nrf8001 with an arduino. I have read up many articles about...
I have seen several good questions and answers on this forum regarding the use of a PA for extending range of the nRF51422/nRF51822 devices. I have a battery-powered application...
Hello everybody,
We are using a nRF51288 with an external DCDC converter. VDD and AVDD is bridged, DCC is not connected.
The software is working in Peripheral mode, S110...
hello,
I recently purchased a NRF51 dongle and NRF51 DK. I was working with older version of NRF51 development kit. I did n't get any information in the user guide provided...
Hello,
when using the S130 with multiple connections and sporadic advertisement and scan procedures, I get a connection timeout after a few minutes, now I must know, how...
Hi,
Im using an app_timer in my application to create a timeout for UART read (im not using SoftDevice).
On my board I have USB and battery power, so at the moment when...
After switching to 51822 in example project nRF_Examples\7.0.1\dfu\bootloader\
I have next output:
compiling pstorage.c... compiling bootloader.c... compiling bootloader_settings_arm...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
