Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I'm trying to get a modified version of the serial "NUS" service to work encrypted with Android 4.4 (API 19). Everything works fine on iOS, but with Android I get ofter...
hi,there
raspberry can ping6 pca10028, rasberry can receive udp packets from pca10028.
but how can i ping6 pca10028 from pc?
env: pca10028 + csr ble dongle + raspberry...
i'm confused of the relationship of wirepas and ant+,both claim to surpport mesh network and multihop.what's more confusing is that both are promoted by nordic.
I look up...
I find in the following example code that if I start my application from a powered-off to a powered-on condition and main() executes the code as shown, everything works fine...
Hi,
I do receive undefined HCI errors in my disconnection handler. I wait for the BLE_GAP_EVT_DISCONNECTED event and use the bleEvent->evt.gap_evt.params.disconnected.reason...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
Hi,
In my project, I need to periodically perform some jobs on the nRF51822 Beacon kit (sdk 7.1). For that, I think I need to use timers. However, I'm not sure how to do...
Hey everyone.,
I was trying to use nrf51822 as spi slave and just a heads up to know that i use Nrf51822 as master. I see that when chip select CS gets low SPI needs to acquire...
I've added a custom service and a few characteristics on the nRF51822. How can I access the current value stored in one of those characteristic outside of a BLE event occurring...
Hi,
I'm unable to run any application on nrf51 DK (Keil used). When I start debug (no matter what application I load), program always cycles between 2 instructions:
0x000006CC...
