hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello,
I noticed the various examples as well as the ble_advertising component all check for pending flash operations and will not start advertising until they are all...
hi guys,
im developing a program to interface accelerometer MMA8452 with nrf51822.so if accelerometer is in peripheral device,how do i send the x,y,z co-ordinates from peripheral...
Hi everybody, i am working with a nrf51822. S110 with sdk6.1 IDE:keil
I want to do FLASH Erase while in a connection.
I have read this page devzone.nordicsemi.com/......
On initialization of the bsp, I get ERROR 4 (NRF_ERROR_NO_MEM) when I define LOCATION.
Why is this? Because it seems rather weird there's no more memory at that point in...
Hi all,
When I start the bootloader using ble_dfu service as-is in my application I get no ble events in the bootloader. When I call the bootloader from the main loop it...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
I am trying to do OTA DFU on nRF51-DK from a BLE dongle (CSR 4.0) and gatttool from BlueZ. The image is compiled from blinky_s110_pca10028 example ( blinky_s110_pca10028.hex...
Hi
I want to program the S120 softdevice over an mbed HRM1017 ([link text] that uses nrf51822. I can program only with CMSIS-DAP or drag and drop over the drive. I am using...
