The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi everyone,
I'm working on a project using the nRF54L05 (v2.9.0) and I'm currently facing an issue with BLE. I want to change the BLE transmit power , and so far I’ve only...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
If the nrf51822 device goes out of range then comes back in range, the application automatically reconnects with the device and tries to read a particular characteristic....
Hi,
We have a set of connected devices in a building of around 22 floors, may be around 6000 devices, can it connected using a nRF52840 Mesh network? Please let me know...
I used the 52810 board, with the SDK14. I modified the 52810 according to the official website related to the relevant definition. I can run the code but it does not print...
I've been searching and wanted to confirm that in SDK13, it's still on us to implement a timeout if a device is placed in DFU mode? As others have said, this just seems such...
Hi,
I am planning to enable autoconnect feature in our app, the same way it is done in nrf-connect app. Is there any way to get the code for nrf-connect app or any other...
Hi there, I was trying out the ADC example which is sampling 10 times the ADC and then generating the event NRF_DRV_ADC_EVT_DONE to process the data.
I extended the handler...
Hi, Im using Nrf51422 DK board.
When I try the ble_app_multilink_central example in the SDK12, it works on the DK board.
But it does not work in NRF51822. (NRF51822 QF AA...
Hello All
I planning make DFU over the air.before going to this experiment i want know some information
Any Soft device is fine or Required specific SD
...
I would like to disable the secure timeout in the bootloader for a specific condition.
I am using nrf52832 chip, sdk 12.2, softdevice s132 v3.0.0 with secure bootloader...
Is possible to use DMA to communicate with nRF24l01 on STM32?
In my test, when Master spi CPOL = 0 and CPHA=0, it can communicate with nRF24l01 by SPI but not accessable...
When plugging the PCA10028 into my PC, LD5 is permanently turned on (or blinking to fast to see it).
But if plug the board into at power outlet, LD5 starts blinking rapidly...
This is more of a feature request:
Can you make the config file path configurable (both config files) ?
This would allow me to create a proper rpm package for a few...
when I use nrfutil.exe to generate .zip file on win10 64bit, I got the UnicodeDecodeError.
Traceback (most recent call last):
File "__main__.py", line 303, in <module...
Hi,
I have tried buttonless DFU in SDK 12, for which I have a few questions
(1) Is bootloader not needed if I use Buttonless DFU Template Application? However, SoftDevice...
I work with gcc on nordic nrf52 SDK13.0.0.
I see the post:
devzone.nordicsemi.com/.../
But if I try to change the packet in the radio_event_handler in active state,...
