Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
We're designing a new revision of our open source sensor beacon platform: http://ruuvi.com
Just want to make sure I got this right. nRF51/2 Reference PCB Guidelines states...
Yeah. It's that topic again.
I tried to measure the current with an oscilloscope (Agilent 100Mhz; 2GSa/s).. but that didn't quite work.
Can you maybe share how you guys...
Hi
I have tried to convert ble_app_uart to use spi slave rather than the uart with no success.
Please can I have some pointers as how to go about it.
Thank you
Hi,
system info:
SDK: v6.0.0.43681
S110 V7.0.0
nRF51822 Rev.2
I’m using a ~4ms one shot timer (using the timer library) which is being started in the...
How can I dynamically assign the MQTT broker address
Hi all,
I have a general question how to assign the MQTT broker address dynamically.
Current Nordic IoT-SDK mqtt...
Hi,
my question is related to this question:
devzone.nordicsemi.com/.../
Erasing Flash pages takes a pretty long time (and the CPU is blocked during this time). For...
Hi,
I use NRF51822 QFAC chip, SDK is 8.1.1, soft device is S110. The base project is ble_app_uart. Now I want to add OTA DFU into my project. But I don't know how to start...
Hey together,
I'm using the GPREGRET register at the nrf52832 to determine how the module should start up after an off mode reset. Thus I set a predefined bit in the GPREGRET...
I have been working on the multilink example lately (version: 8.0), I have identified the function to send data on the peripheral part, it is sd_ble_gatts_hvx(), but I'm having...
hello ,
my IDE is keil and the sdk is nRF51_SDK_10. i know the system is 16M frequency,but now i only have 32M crystal.How can i change the sdk if i wang to run the system...
hello , Nordic Engineers. my IDE is keil and the sdk is nRF51_SDK_10 and s110_nrf51_8.0.0_softdevice.hex. The project is "C:\Users\robben\Desktop\nRF51_SDK_10\nRF51_SDK_10...
Hi,
I am trying to load hex file over the air for nordic but I am getting error as master emulator installation not found. Please suggest. I am using MCP of version 3.10...
hello i want To use mbed for nrf51 dk. i used this link developer.mbed.org/.../ . i am following steps but i can't copy hex file into bootloader. i got error message "There...
Hi,all
my question is in the title.
i am making a project like NUS (sample in SDK).
i found that during the data transmission Situation，the write without response...
