I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
hi,
i want to make BLE central node with Nrf52840 for receiving multiple data from Nordic thingy 52,i am using keil IDE with Nordic sdk 14.2.0 and blinkey central(s140_PCA10056...
Is this possible to change MTU Size in nrf51822 Board from 23 to 43?
is any changes is done android side app? the application is same copy of nrf Toolbox UART app.
please...
Hi, everyone,
I am developing the project on nRF518522 and I must use the flash memory to save the data. The data must be saved while the device is conncted via BT with...
hi,
When using the UART examples I found that as long as I opened the uart_init () program will not work, debug the discovery process will be executed
case APP_UART_COMMUNICATION_ERROR...
Hi,
I am trying to develop an application which recieves data over SPI and I want to send this data over ble, I am using NUS service. I am recieving 5 bytes over SPI at...
Hello,
I'm using 2 nRF58840 dev kit with SDK 14.2.0.
I'm trying to read the RSSI value of the second board from the first board using LE Coded PHY in both modules.
...
Hi every body , i have some issue if you don't mind. i rooted a board with NRF52832 SOC without PCA. i want to get a uart connection with pin 8 and 10 . It s possible to do...
Hi,
I am wondering if its possible to download a fds record on android device when connected ?
I want to save data and retrieve it when I get connected to it.
Th...
hi team, i want to edit my uuid, major and minor. i searching for the example. i am using nrf52840. i didnt get any example. but there is a example for nrf51 ble_app_beacon_bcs...
infocenter.nordicsemi.com/.../nwp_015.pdf
Above refered white paper says:
"refer to the Nordic Semiconductor white paper ‘nRF TX measurements’ for procedures on how to...
Is it possible to set two nRF52 as duplex MODEM?
The objective is to monitor a remote solar powered device from a PC. There would be one nRF52 device at each end (one at...
