Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello every!
I was transmit data from point1 to point2 with two nrf52840 board. Now I want to do forward this data to point3. Can i do that and how to implement? Have any...
Hi,
I have used fstorage to save data in flash in SDK V13.0 with S132. But in the SDK v14, it have changed so many such as fs_config_t struct has been removed and I don...
Arms labs published some Bluetooth stack vulnerability
go.armis.com/.../BlueBorne Technical White Paper-1.pdf
Nordic answered that BlueBorce is no effect for LE.
...
Dear Nordic,
nRF52840 is very good solution and we are planning below.
What I want to do:
WLAN Firmware to be stored in nRF52840 Flash
nRF52840 Flash is sufficient...
When I am using power manage function to keep device low power mode, for every 6 milliseconds I am getting small spike of ~300 micro Amp and average current of 300 micro Amp...
Hello Sir,
I’ve been used nRF24L01P controlled by DSP to transmit and receive data for few months. The nRF24L01P is run in 1Mbps mode. The SPI of DSP is set to send 8 bits...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I have read a lot posts which has the same title unfortunately I am still unable to solve my problem. I am using pca10028, s110, SDK 6. Code is based on BLE_app_uart...
Hello,
on my computer I have the IAR Workbench (8.11) installed.
I want to start Bluetooth software development.
Therefore I installed nRFgo, unzipped the nRF5_SDK_14...
Hello
in sdk14.1 in examples/ble_peripheral/ble_app_buttonless_dfu i get this error when compiling with g++:
make[1]: Entering directory '/home/work/software/nordic/sdk...
Hello,I want to make NRF_LOG_BACKEND_UART work with NUS . The nus work with app_uart_fifo,and the NRF_LOG_BACKEND_UART work with app_uart. I try to make them work together...
I am using NRF51822,S110,16Mhz XOsc. In this if Controller goes to sleep mode the current consumption is 4.9mA. In my application at sleep mode BLE should be connected and...
If I make a product using the nrf24lu1+ chip how can I register a PID for it? The VID is 0x1915 and I know that Bitcraze uses a PID of 0x7777. The Linksys WUSB11 v2.8 802...
