Hi,
Our team is interested in WiFi location service in Cloud Services.
https://www.nordicsemi.com/Products/Cloud-services/Location-Services
However, under the WiFi...
Hello,
I am using Nordic Thingy91 5G board. My modem firmware version is 1.3.6. My nRF Connect for Desktop version is 5.2.0, which has a Serial Terminal version of 1.5...
Hi,
I'd like to know how can I implement a Scene Server for one or more Generic Onoff Servers (typically leds).
I read the documentation related to Scene Server and I...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
Hi
I've an application running on nRF Conenct SDK 3.0.2 on an nRF52840DK. Now I tried to enable update support over serial recovery of MCUBoot using the USB ACM.
First...
I have created the nRF Cloud Multiservice Sample application and would like to add WIFI support.
I am using nRF9151 with nRF7002 EK hardware and would like help in adding...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
Hey,
I want to read the value of characteristic of conneceted peripheral. I'm using two BLE modules, one is peripheral and one is central. I connected with central to peripheral...
Hi. I have several questions about mbr.
1). Will mbr finish to write after unexpected power off?
2). Can I copy softdevice + application or only application using sd_mbr_command_copy_sd...
Hello,
We are trying to put togheter a custom mesh communication protocol based on nrf24L01+. Everything was good until we made transmission tests outside, from ground...
Nordic board nRF52 PCA10040, V1.1.1, 2017.1, 682048249.
The pins CTS, RxD, RTS and TxD are currently driven by the MCU. I want to use the SPIS0 in the nRF52832 with the pins...
Is there a Setting in IAR to program nrf52832 without Power cycling
nrf52832 does not start after programming from IAR IDE, using J-Link
But..
For both With J-Link...
I have been experimenting with using some peripherals on the nrf52832 without using the SDK. Primarily of interest to me right now is the low power comparator (LPCOMP).
...
i use nrf52832 .i want to connect device and send advertisment data at the same time. But peripheral mode cannot connct device and send advertisment at the same time. central...
Hi!
I am sorry if I had repeated questions in this forum. I would like to understand few things.
Test scenario
Central - nRF52840
Peripheral - nRF52840
Bluetooth...
I want to add wdt function in ble_app_uart. Please tell me where should I feed the wdt.
in below main loop?
for (;;)
{
power_manage();
nrf_drv_wdt_channel_feed(m_channel_id...
I'm trying to decide the best way to be able to have sub millisecond time keeping, but keep the processor sleeping until it gets a hardware interrupt.
Basically I need...
Hello Nordics Developer
I'm from indonesia, i'm electronics designer, i have develop new products using BLE, first develop i'm using nrf51 series but And my boss ask is there...
I'm trying to conserve space in the advertising packet, and would like to free up the space used by the 128 bit (16 byte) service item list, as this takes a minimum of 18...
Hello all,
I am working on nrf51 series for mesh application so regarding Pre addressing of controller how will get to know the adresses of SOC's in mesh network?
can...
I am using the nRF51822 with the s130 softdevice, and I would like to control three RGB LED modules with three PWMs (R, G, and B). For various conditions, either one, two...
[CONDITION]
1. R1 = 1.5M, R2 = 430K
2. GAIN = 1/2
3. RESOLUTION = 10bits
4. Single End
[ISSUE DESCRIPTION]
1. If voltage is changed by 0.1V step (4.1V -> 4.0V), the...
