Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Helllo All,
I designed on custom board (nrf51822 and used 4 programming pins(swck,swi,gnd,vcc) but how to program/flash the soc?which segger i need to purchase?
Hi There,
I am
Using Linux as host platform
I'm able to successfully compile and download the example to the nrf52dk.
But I didn't understand how to debug the example...
I'd like to get peer address after the connection between nRF52 and other 6lowpan device is established. This address will be then used to create a TCP connection with some...
Hi All,
I am using the Nordic nRF52 nrf52832 device to read a value in from an Android device. The value will be between 5 and 60 seconds. I'm using the experimental_ble_app_blinky...
I would like to change UUID programatically,initially we are trying to establish connection between phone and beacon.
We tried to change BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
Hello, nordic team；
I want to create a DFU for the ANR + BLE device in the nRF5_SDK_12.3.0_d7731ad \ examples \ dfu \ experimental_ant_bootloader routine.But I use this routine...
Could someone explain the difference between the following functions:
ble_conn_params_change_conn_params(ble_gap_conn_params_t *new_params)
sd_ble_gap_conn_param_update...
Hi all,
i need to have at one to one connection(one phone on one nrf52). I have created a whitelist.
What i can see is that after a pairing and a bonding, if i delete...
Hello,
I'm working on an UART application which uses experimental_bootloader_secure_serial bootloader. I've done a similar thing before with SDK-11 (though not a secure...
Hi,I use S130 V1.0 working as a master,and connect a device.My device adverting interval is 800ms， and gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//MIN_CONN_INTERVAL...
So I thought I would upgrade one of my projects to SDK13 and try out SES 3.24 at the same time. I thought I would start by getting the ble_app_uart_pca10040_s132 project to...
Hi.
I just want to upload BSP package to my NRF51 DK via mbed web app, but i can not find proper source from all the available projects in mbed. Tutorial of BSP also doesnt...
Hi,
i set the app_timer to fire every 60 seconds
app_timer_start(m_Timer_id, APP_TIMER_TICKS(60000, APP_TIMER_PRESCALER), NULL);
Is it possible to get the current couter...
Hi,
I have changed the ble_app_uart_c example so that it can connect to multiple peripherals(at the moment 2 peripherals, the goal is 3 peripherals). It works fine, but as...
