Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
Hi all,
I have a working ADC implementation (S130 + Application) and use it to measure an analog input continuously.
However if I use the same code on top of bootloader...
When I have a test using nRF24l01+ with STM32, I can only get a playload datarate no more than 450kbps using nRF24l01+ 2M mode.
How can increase the playload data rate and...
I have been using two NRF24L01 to communicate with each other using just simple Arduino Uno Board.
it worked for 5 days and now all of a sudden it is now working.
I tried...
Hi,
in order to add flash programming support to the iSYSTEM toolchain based on a
customer request I would need a flash reference driver/monitor implementation.
Would...
The sync time for my nrf2460 seems to be about 4 seconds. Is this normal? Secondly, once
the pair is synced at close distance, one or two feet, as I move away sync is lost...
I'm planning on having all of the different Device Information Service characteristics (fw_revision, sw_revision etc) with each being just a single integer for version number...
Can someone tell me what these errors actually mean
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -1.
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -102.
...
I am using nrf52840 central and nrf52840 peripheral device. Ble communication is enabled between and data transmission is working. I would like to analyse the packet loss...
