Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
We are using S132. Our application has several proprietary services. Once with writable characteristic to which we would like to send a response. So basically a mobile application...
Firstly sorry for my bad english.
I wanna make a data logger and i am using fstorage module. Before advertising start everything works correctly. However, when advertising...
Hi,
I wanted to USE BLE and ANT with nRF51422 chip, is it possible to use the S310 which is in the SDK10 with the updated functions in SDK12.30? or is there another way of...
It seems after my last round of Window 8.1 updates the Nordic Sniffer no longer functions properly. When I run the Sniffer software, it only can scan for about 1 second before...
My nRF52 device has been flashed with the Legacy Bootloader from SDK v11.0.0 and now I want to update to the new Secure Bootloader in SDK v12.x.0. However, when I try to update...
Hi
We use ble_app_uart_pca10040 app.
We have our own board has microcontroller and send data over uart to ble module (bmd350)
There is Nrf52832.
I want to send 32byte...
Hi. I’m developing software on nRF51822 with SoftDevice s130-v2.0.1 and SDK v12.3.
I want to apply RTX to the software. In the case of building it using arm-gcc, the software...
Hi,
I am developing a project with NRF51822 and i want to block signals in one direction. Is it possible ? And if it is possible, how can i do this ?
Thanks !
(PLEASE SEE COMMENT BELOW)
I've got a Nordic project that I imported into Eclipse as a makefile project. I've got it working and I can debug into it. Everything is good....
OTA problem：
My hardware is 51822qfaa .
This my bootloader: nRF51_SDK_10.0.0_dc26b5e.rar
location: nRF51_SDK_10.0.0_dc26b5e\examples\dfu\bootloader\pca10028\dual_bank_ble_s110...
how many uart can I use at the same time in nrf52832
i know in nrf51822, every pin can use as uart,but at the same time ,i can only use one uart.and now ,i have a case...
Hi,
I have an issue with app_timer (nRF52, SDK13.0).
I use a single shot timer.
I try to debug, and I'm in the case of app_timer.c line 650:
ticks latest: 534879...
