Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi,
I need to implement a simple external interrupt triggered by another IC on a nrf51822.
After searching the devzone I found the example in the GIT repo ( github.com...
My code is roughly based on:
devzone.nordicsemi.com/.../
I'm using SDK12.2, softdevice S132. The relevant parts of code are:
static uint8_t bapi_adv_data[14] = {...
we are facing issue of "application program" hex file generation, which is different in two machine . we are matching setting of both machine , we found the difference in...
Hi,
I've got a problem with nrfutil package on Raspberry Pi with Python 2.7.9 and pip 1.5.6 included to raspbian distribution.
I'm writing like below:
pi@raspberrypi...
Using SDK 12.1.0 with flash containing data from a previous version of software.
The pages_init function in fds.c does no have adequate protection to prevent writing to...
Hello,
I have followed a couple of the posts on the devzone on how to increase the MTU and add the DLE support such as this .
However, whenever I send over 20 bytes...
hi, i have a SIM800L Core board which is using UART protocol to communicate or to send At commands. so that i am using BLE_APP_UART example to set AT commands to SIM800L....
Trying to follow this tutorial using KEIL 5.23, J-Link 6.14b and the DK.
I am getting linking errors like this when compiling:
What did I do wrong and how can I fix...
hi,
i was looking for example of two nrf52 communication. One is central of course and other one is peripheral. But i have following doubts.
If one is central then...
What is the right way of stopping and then subsequently re-starting SAADC?
Using the saadc example, I want to be able to stop saadc when a certain pin is grounded or when...
Hi,
I just found the following example:
infocenter.nordicsemi.com/index.jsp
There the baudrate 115200 is set by default. If I calculate the bit rate (8 data bits one...
Hello,
I use two NRF24LE1 emission and reception when I use a simple ACK is good but with ACK payload, there is a problem,
I do not really see where you can help me,
Thank...
In an answer to this question about current usage of pull-ups here , RK and Vidar comment:
Is the GPIO you have configured as a pull up, being pulled down? If so you...
How to save data persistently(non-volatile) to nRF51 core not effected by powering off and on?
(How to save static data persistently without deleted when the core is turned...
Hi,
I have just used some code from your flash_write example in the SDK, it works ok but i have a couple of issues, the code is from sdk 12.7, and the chip is an nrf51422...
