Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I'm using nrf51822 and ble_app_uart(SDK 12.3.0).
I'm sending data from my android phone.
My question is that what happen if send data before previous data is...
Hi!
I am developing application for thread on NRF52840. I've got one problem with connection stability. Sometimes some SED nodes are disappearing. Only reset makes them to...
I am using CC2541 and CC2540 (USB dongle) which will communicate with each other and transfers data. I want to know weather i can communicate to CC2541 (ble device) directly...
Hello,
We have a setup where we connect an nrf51822 and an iphone.The nrf51822 connects to the iphone,
notifies the data and disconnects roughly every minute.(This is done...
There are only HID periphral sample code in nRF52840 SDK.
It is difficult for me to implement HID central with the sample and tutorial provided.
So I want to get a sample...
Capture_Load_error.PNG
All,
I'm new to the nodic. Just now installed KEIL V5.24.2.0.'m able to compile code but not able to load it on Target.
Please find attachment...
Hello,
It doesn't seem possible to mimic a IEEE public BLE MAC address using the BLE stack provided by Noridc. But how easy is it for others to roll their own BLE stack that...
For longer than I'd like to admit, I've been trying to make an application on the NRF52832 that relays UART data to a phone. To date, I've:
Gotten the BLE_APP_UART application...
hello all：
I think sdk13.1 s132 has a bug about ANCS，
ANCS works normally only in the following two cases
1、Both the phone side and the device side do not remember...
I have a sensor with serial protocol of 7 bits data, even parity, 2 stop bits. I wanted to use uart library to interface with this sensor. But I couldn't find the settings...
Some times when I'm trying to use GDB it stop with the following information:
(gdb) file _build/nrf51822_xxab.out
A program is being debugged already.
Are you sure you...
I started to try SAADC example in SDK12.3. After setting up project in eclipse, I got two errors:
Symbol "NRF_TIMER0" could not be resolved
Symbol "TIMER0_CC_NUM" could...
Hi,
We are a group of students at NTNU looking at the possibility of creating a small device that connects to your phone and multiple other BT devices simultaneously, letting...
Hello,
This is a quick question regarding the behavior of the Power Supervisor POF warning. We implemented a fairly naive use of the POF warning where we would log an POF...
Hello I am using the NRF52832 in ESB mode. I use both VERIFY_SUCCESS() and APP_ERROR_CHECK() within my code in various places but when am I supposed to use versus the other...
