Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I have taken ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0 and i integrated Alert Notification Service,DIS[device information service] and DFU... Device...
I'm using the latest version of Keil with Software Packs. As I understood, copies of configurable files are stored in RTE folder. Non-configurable files are stored inside...
When i connect the board to pc its not detected and No J-link device in device manager
But when i press and hold the IF BOOT/RESET button and power cycle the board the LED5...
Hi,
I want to advertise the beacon with its name visible using the ble_app_beacon example but not able to understand how to proceed.
With this, I am not getting how can...
I want to make the led ON always and making the source code from scratch in keil mu vision 5. I am not able to understand which library is to used and how to proceed.
I'm using nRF51822 to communicate with nRF24L01+ without SoftDevice, and it is working fine.
But when I add app_timer.c to the project and compile, it will show the following...
Hi,
I am able to program my custom board using nrf52dk (only 32 Mhz osc populated on custom board), and I can also see the output of SEGGER_RTT_WriteString() though JLinkRTTClient...
We've been suffering Unreliable Auto Connection for quite a while... "autoConnect" sometimes just doesn't work to get the device back to connection. Below is the failure message...
Hello,
I started with example apps and have got one working with the supplied makefiles, gcc, and Eclipse. I'm able to debug my code without trouble, and have succeeded...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
Hi Team,
I´am working with the nRF51422 and would like to change the parity from even to odd.
Is there any possibility to change that setting or just to invert the even...
Hello,
Is there any possibility to configure the UART parity to odd on chip?
I am using the nRF51822 chip. I could activate the parity but inside the documentation they...
Hello
I am building bootloader. I do not use Softdevice and used example from this topic . Bootloader must read FW from uSD card, update flash and jump to application....
I am using nrf52 , it's always connected to an iPhone, and I need a truly real time respond.
I am sending short messages, like 2 characters at a time, and play a sound on...
