I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
Is there any information on how much improvement the DCDC has over the LDO at 1.8V? I'm working on a heavily space-constrained application, and I'm trying to make a decision...
Hi, i am working on PWM Library example in which i a m configuared GPIO pin P0.25. then i am getting voltage variations 1.3 to 2.8 volts.
the problem is when i disable...
Hi,
I want to connect old nokia 3310 to NRF52 DK.
Please let me know if any one has information about it?
Based on my research old nokia phone uses M bus and F bus...
Hi,
We're working with very specific hardware which requires us to watch very closely. We're currently considering a blocking function in an ble event handler which can...
Hi all,
We are currently developing a BLE enabled sensor device. We want to use the NFC component to identify the sensor by writing a device ID to the tag.
Question...
Hi,
The comparator (COMP) in nRF52 can use three internal reference voltages (1.2, 1.8 and 2.4V). Is it possible to also output these voltages on IOs?
Best regards
...
hello there in my code,
APP_ADV_INTERVAL 64
APP_ADV_TIMEOUT_IN_SECONDS 5
using nrfsniffer i am getting 57 packets in 1 second.
i can't understand it. because APP_ADV_INTERVAL...
Hi!
I tried to some research in the forum but I would like you to assert my final decision.
My goal is to design a sensors network (at the beginning with five end-nodes...
I am working with some code from a previous provider and I found in its void bsp_event_handler(bsp_event_t event) function this code:
case BSP_EVENT_MID_PRESS:
err_code...
Not sure if this is the proper venue for a bug report:
In nrf_nvmc.h (from SDK v12.2.0)
/**
* @brief Write consecutive words to flash.
*
* @param address Address...
Hi,
We need to add WeChat / AirSync functionality to our nRF52-based product. Is there any support available from Nordic for this kind of environment? For example ble_wechat_service...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
hi，
i can't find the ID for softdevice_s140
run cmd ： nrfutil pkg generate –help
--sd-req TEXT The SoftDevice requirements. A comma-
separated list of SoftDevice...
