Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi,
My code was working perfectly until yesterday, where the function "ble_nus_string_send" on my main loop started returning NRF_ERROR_INVALID_STATE because "p_nus->is_notification_enabled...
Hi,
I have found that the sdk13.0 is support 20 current connections , I test it by using example /SDK13.0/example/ble_central/ble_app_multilink_central , I change the central...
Greetings Nords,
total noob here,
I've got two preview nRF52840 devices (as well as the two normal nRF52 devices),
I want my two preview devices to be able to ping each...
Hi,
I am using nRF52 and SDK13 with SoftDevice 132 v 4.0.2 which is now supporting multi-peripheral connections.
I am using multi-peripheral example for reference. In...
How to make BLE examples working. for nRF52DK series (BLE_app_template)?
Hi, I tried for around a week. and I will describe what I did, and what I have found first.
I...
We have IoT gadget, where we use coin cell (CR2032) as power supply. Now, we would like to connect U_bat directly to ADC to measure battery level every n minutes, but keep...
Hi.
I have an NRF52DK Board. With the built in JLINK Debugger it works fine. Now i bougt an KEIL ULINKpro Debugger. Is connected with the 10 Pin cable. And i cannot flash...
Hello.
I'm working this : github.com/.../pc-ble-driver
In Chapter: Compiling the connectivity .hex files
2.Apply the patch hex/sd_api_v/SDK_connectivity.patch from...
Hi!
I have 2 nRF52 custom designed PCB. Is it possible to develop android app that connect both nRF52 PCB at the same time and receive the data from them at the same time...
I keep having problems like frequent disconnects (reason 0x08 = BLE_HCI_CONNECTION_TIMEOUT) and NRF_FAULT_ID_SD_ASSERT on my NRF52832 (tested with S132 v3.1.0 and V5.0.0-alpha1...
In the API file nrf_drv_twis.h for the nRF SDK, the definition of NRF_DRV_TWIS_DEFAULT_CONFIG looks interesting. The definitions for SCL and SDA pins are both set to the same...
Hello,
Is it possible to have 170 characters long device name somehow to the nRF52832 so that standard Android phones are able to see it without any pairing or any other...
In ANCS example (SDK 11.0.0)
I thought keys list distributed should be the same naturally until I see the code below.
ret_code_t dm_register( dm_application_instance_t...
I saw following code configuring about permission of charateristic value R/W.
it's in uart example of SDK 11.0.0.
static uint32_t tx_char_add (ble_nus_t * p_nus, const...
