I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I create software uart librarty for nrf52832. For one pair tx, rx it's worked (on 9600, 19200 baudrates). Then I create multi-instance software uart (all of them gonna use...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
The SAADC on the nRF52832 consistently reads 20-30mV low, regardless of the source (AIN channel or VCC), Tacq, Resolution, or gain. All of the measurements are using the internal...
HEllo,
I am trying to set up a whitelist advertising and scanning, and while the advertising seems to go fine, I am getting an APP_ERROR:ERROR:Fatal on my central while...
Hello all,
Accordingly with nrf52832 product especitifation when radio Rx is active there's a additional 5.4mA consumption. My doubt is how softdevice s132 handles the Rx...
hi!
i am working with the nrf52 and i am looking for a timed sleep mode, meaning, a function that goes into sleep mode for a given duration.
is there anything like that...
Hi all,
I am working on my Central device to request pairing to my peripheral ( I asked about the peripheral in my previous post , both are running a nRF52DK and SDK13...
We have shifted our development from nrf51422 QFAC (32kB RAM and 256 kB Flash) to nrf51822 QFAA (16kB RAM and 256 kB Flash).
I'm unable to run dual bank ble bootloader...
Hello,
I would like to signalize that the DFU process is running. I mean when I start to upload the application into the CPU, then a LED (for example) is ON, after uploading...
We have been successfully using the Softdevice s132 to communicate with a smartphone using BLE. However, we have run into an issue with the compliance testing in the new requirement...
Hi All,
I am a beginner in app development. I am working on a project where i am supposed to transfer texts to my pca10040. Although i wanted know if i can modify nRF Toolbox...
I'm taking a look at the timeslot API example here , which was linked to in the answer to this question .
Very interesting! As I gather from the documentation for S110...
Hi,
I would like to have accurate (1-5ms), synchronized timestamps for logging events from a set of nRF5x boards, spaced tens of meters apart. Each nRF5x board is connected...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I am struggling to find a starting point to be able to program the beacons. I'm completely new to this but want to be able to change the tx power so that they are only visible...
