I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I have been experimenting with the mbed BLE Health Thermometer examples, BLE_Themometer etc. Whilst they are visible and show their name in the nRF Toolbox Health Thermometer...
Hello,
with Android 5.0 BLE central and S110 8.0 peripheral I do this:
Erase all bonds in device_manager_peripheral.c
Check that m_peer_table contains zero...
Hi,
I would like to convert a blinky project for the BOARD_PCA10040 to my own custom board. I can't find on eclipse where "#define BOARD_PCA10040" symbol is defined so I...
Hi,
I'm trying to config my device with resolvable private addr (RPA) as code below:
rpa_add.addr_type=BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE;
sd_ble_gap_address_set...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
