Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
I am making HID composite devices, but I find that if the number of report ids is more than 5, I cannot send data from PC to this device；Error code 1784 is displayed
If...
Now I'm developping a USB MSC project, the Nand flash size is 4GB, I don't know how to set USB capaticy size.
I change the setting in nrf_serial_flash_params.c:
static...
Use the media control's volume up / down keys to control the camera shooting of your Android camera. How to achieve continuous shooting?
How to achieve the function of camera...
HI
I'm writing a programm the using a nus as its service, because nus is a custom service there is something that need to be changed, I followed the tutorial about making...
Objective: I want to read 64MB data stored in external flash (interfaced with nrf52840) from android mobile App (specific: One Plus 7T)
SDK: nRF5 SDK v16.0.0
Soft Device...
Dear,
Im trying to measure the RSSI with THINGY:91, I found on the document nrf91_at_commands_v1.1.pdf about
1. AT+CSQ
+CSQ: <rssi>,<ber>
Note: Not detectable, RAT...
Hi!
I am currently working on a project where i would like to use Thingy:91 as MCU board as it contains other features i need to use, like 4G and GPS.
The problem is that...
Hi I'm currently develop new product based on RAK8212. I have problem with reprogramming devices. Programmer i use is nRF52-DK I'm not able to reprogram about 10% of devices...
Hello,
I have a low power application, which is activated by a push button press. (The DC-DC converter is also in shutdown mode normally, so the NRF9160 does not have power...
I am occasionally (very rarely) getting "Mesh assert at 0x00037996", but when I try to look this up, I get:
My understanding is that this means the mesh_assert is...
Hello, this is the nrf52833/52820 design drawn by the customer, because this is our first contact, please help to check whether it is reasonable? thank you.
Hello,
I'm working on a BLE app on an Arduino Nano 33 BLE, which is equiped with an nrf52840. I'm struggling to increase my BLE transfer speed ( i think due to the limitations...
Actually i was working on 3 boards, nRF51422,nRF51822 & nRF52840. While executing some examples on each board i realised that each board has its specific pca hex file to be...
I n the main of my program I have this( UBLOX_PWR_PIN = Pin16 of nrf ),
uart_init(); nrf_gpio_cfg_output(UBLOX_PWR_PIN); nrf_gpio_pin_set(UBLOX_PWR_PIN); nrf_delay_ms(200...
Hello,
I've a problem with a PPK board.
When the current go over 10mA the value reported is wrong, in my case should be 15mA and PPK measure 80mA and more. Instead, in...
