Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Using LFCLK, enabling and running the WDT causes the nRF52840 to hang until the watchdog reset when calling nrf_drv_clock_lfclk_release . This is with SDK v15.2.0 Steps to...
Hi I'm using nRF52 DK to program a BM832 module where I want to run some code to manage FLASH memory. I make run examples on the DK but on BM832 module can't be possible because...
Hello Nordic Community!
I have seen previous posts mentioning that the DFU example was not working with SDK 15.3 ( Getting started blog ). But in my case I was able to...
Hi all,
I am working on a new project and I need to communicate to a sensor using I2C, then save the data on a flash (files visible on windows as mass storage via USB) and...
Hi,
I am developing an application where the device should support both central and peripheral roles at the same time. My devices are connecting to a mobile phone. All the...
Hi, I use the nRF52840-DK together with a secure element (Infineon Trust X) and want to measure current/powerconsumption of this whole setup during certain operations. At...
Hello!
I'm currently trying to run the mqtt_simple sample (latest version of nrf-zephyr) on the nrf9160 DK. Unfortunately it is not working, because getaddrinfo() returns...
Hi,
I am using the nRF Connect SDK to develop software for a nRF5340_PDK focusing on Security and power efficiency. Therefore I wanted to make use of the CryptoCell-312...
Hello,
The release-notes of the Modem Firmware v1.0.0 for the nRF9160 state that there is now "Support for DNS server address setting by application.". However, I cannot...
After updating to nRF9160 mode firmware v1.1.1 there have been several vector catches. I have not updated Zephyr or anything else from the latest version downloaded on 9/24...
Hi,
I have programmed my Nordic Thingy 91 with lte_ble_gateway and seems to work fine. However whenever I increase the connection parameters, the thingy91 fails in the discoverty...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
