Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello, I'm trying to use the PDM in the nrf9160. I'm using SDK tag 1.2.n I added
#include <nrfx_pdm.h> at the top of my main.c file.
I put
CONFIG_NRFX_PDM=y
in the...
We seem to be seeing slowness in a bare metal implementation. We would like to confirm the nrf52832 CPU speed. How can this be confirmed from within the codebase and/or logger...
Hi All,
Does anyone know what the maximum altitude is available for the nRF9160 GPS?
I know some GPS devices stop working properly if above pre defined heights.
The...
I have a PCA10040 board and use the development soft of SEGGER Embedded Studio for ARM 4.50.
I ran the project \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_beacon...
While I was working with my dev kit this morning, the board has suddenly stopped responding to commands.
When I attempt to connect via jlink using Segger Embedded Studio...
This is definitely a stupid question but the uart ble example is littered with the likes of " NRF_LOG_INFO("Connected");". Where is this printed and how can I view it? I can...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
is it possible to use use timeslot API on s140 while BLE is in "central" mode?
I was able to use timeslot API when BLE was running as peripheral. However, same...
Hi,
I need the bigger the size of bootloader. So I changed IROM1 0x78000 0x6000 to IROM1 0x77000 0x7000.But nrf_dfu_transports_init returned error code after I changed the...
Hello I would like to use the malloc function but the function send me all the time a null pointer... I have the same problem on all examples. In this case, I use the "ble_thread_dyn_template_pca10056_S140...
Dear all,
the latest documentation I have found for the "nRF5x Command Line Tools" is version 9.4.0. Is this still valid and sufficient for the recent version 10.7.0 ? ...
I have a BLE device which I can connect to with nRF Connect on Android (v. 9, Samsung Galaxy S8).
After disconnecting in the devices tab, the connection is opened and closed...
Hi, Im developing a Zigbee concentrator. I used nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 ble_zigbee_template as start point of my project. The project is full working...
Hi Nordic,
There is a question about the default setting for Advertising PHY type. if there is no config value setting like case (PHY_1M ) . (all memory already set to 0...
