Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi All
Now I am testing the example code \examples\ble_peripheral\ble_app_uart with Nordic nRF Connect app on smart phone. i do a limit change in function uart_event_handle...
Hi,Master:
Platform: nrf52840
Bluetooth protocol stack: s140
When using qspi to communicate with external flash (communication speed 32M), occasional qspi communication...
Hi,
I have been working with different boards to implement different ML TensorFlow Lite samples in the 52840. I used Particle and Arduino BLE Sense.
All forks from the...
Hello,
I have programmed Fanstel BC832 module with S132 and ble_app_blinky example successfully and I can see the advertisement of BC832 on nRF Connect app. The thing is...
Hi,
I am trying to render some chinese strings on an OLED display. For this I would like to concatenate some strings using swprintf.
But when the replacement string contains...
Hi,
I am trying to flash my nrf52840 dongle via nrfconnect, but it doesn't work.
My project is based on BlueTooth and ZigBee connectivities, so I opened the programmer...
Hi there
I am currently trying to wakeup from system On mode using the DETECT signal and Port Event.
According to the product specification:
Trying to put the system...
Hello,
I'm using zephyr logging APIs to print to serial port. If I log too quickly the output is not correct. Running the code below I get
[00:00:00.626,464] <inf>[00...
Hi,
I am developing a new design using your nRF9160(using LTE ONLY targeted for the US /FCC) + NRF52840 ( using BLE ONLY)
I have noticed that in both the reference designs...
Hi,
We are using NRF52840 in our project. Here my doubt is we need to read the voltage from the sensor which will vary from 0 to 5 v .Can you plz tell me which example program...
Hi, I added the SAADC feature to a beacon project so I can measure the battery voltage. Interesting thing is that my readings always show around 100mV less then VDD voltage...
We are developing a small BLE device and want to make sure we follow reasonable security standards. What type of communication security would a typical device like headphones...
Hi,
I want to change the pin configuration for the uart2. I change it in the SES 's Project>Edit Device Tree .
However, if I change the tx pin to 0x0f , it cannot send...
Hello, Is there any NFC sample for Thingy:91 . I need to connect a device to Thingy:91 using NFC for a project. I am using v1.1.0 tag of ncs repo.To understand how NFC libraries...
