Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
We are finishing up a project with the nRF52832 based on the Nordic Thingy. Most of what we want it to do are normal functions of the Nordic Thingy. It connects to a mobile...
Hi Nordic Team,
In my BLE project when I was trying to add Device information Service(GATT) in BLE central multilink example code, once the connection between central and...
Hi,
I am trying to modify the code in the BLE_App_Buttonless_DFU_pca10040_s132 example is SES. Without any modification the code compiles fine and can be recognized by nRF...
My issue like this ticket
https://devzone.nordicsemi.com/f/nordic-q-a/39428/usb-msc-corruption
I suspect it is caused by a problem in the implementation of the NRF_BLOCK_DEV_QSPI_FLAG_CACHE_WRITEBACK...
Hi,
We encountered a problem when added new models through an OTA DFU. Specifically we upgraded a device with SoftDevice 6.1.0, SDK 15.2 and Mesh SDK 3.1.0 to SoftDevice...
Is it enough just to connect from custom board to P20 header(nrf52840-dk) SWDIO, SWCLK, RESET, from custom board GND to P20( GND_DETECT) and power supply to custom board from...
I need to enable UART1 in runtime in order to be able to read some data coming on that device.
In order to be able to use the uart functionality, I need to set CONFIG_SERIAL...
Hi,
As the subject description, I just remove the part of hid function from main.c then make the personal source file.
Before I removed, the project could work as usual...
Dear Nordic
there are two question find in my software. it may be some matter with thest two question, so put here together.
1.
My software will be reset about several...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
