I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
now I'm on going NRF24LE1 project to low power mode. I try to find several reference as link below, but both of them can't open, someone can help me ?
https://www.nordicsemi...
I have just purchased a nRF52840-DK
I am following the getting started tutorial and when I scan for devices the Nordic_prox device is not appearing in the device list but...
Is it possible to use the NRF cloud outside the dev kits? Working on a custom pcb with custom software and would like to use NRF cloud for it.
---- Christopher
Hi ,
I am working on NRF DFU firmware update. for that i am using secure bootloader code .
I tried with the of way of flasing bootloader code on my custom board and sent...
Hello Nordic community,
I updated latest modem firmware v1.1.0 in nRF9160 custom board. After flashing application code into custom hardware I power off and power on board...
Hello,
I have a question about hardware for Bluetooth LE Audio.
I see Nordic is working on a dev kit:
https://blog.nordicsemi.com/getconnected/le-audio-unveiled-as-the...
HI
I am programming NRF52840 dongle using nrf52840 dk
i have flashed blinky code to my nrf52840 dongle it programmed sucessfully after that i have erased the dongle by...
Hi there,
I'm trying to use the aws_fota example with nrf9160 and AWS and it works fine. The problem is that in my country we don't have LTE-M, so we decided to use a...
Hi,
My application returns ERROR 8 [NRF_ERROR_INVALID_STATE] after I click disconnect in the app "nRF connect for mobile" .This error is returned by "ble_advertising_start...
I try to run samples/bluetooth/scan_adv on nRF52840/nRF5340 using nRF BLE Controller..
Result is nRF52840/active scan: 498 packet/s nRF52840/passive scan: 507 packet/s ...
i have done read and write operations on fds with dummy buffer. now when im writing new data into fds it is showing the previous data .can anyone give the function to erase...
I am trying to build a solution based on the nrf_ble_uart_c example. Building has been working fine until I added pin configuration statements.
I've tried relocating the...
I am incorporating the "pin_change_int" code to generate GPIOTE interrupts from an external device. I made a couple changes including renaming the function from gpio_init...
Hello,
I've been playing around with with the nRFsniffer for a couple weeks now. Adafruit was out of stock of the BlueFruit LE Sniffer so I ordered a BLE400 and a few Core51822...
I would like to program the NRF52810 with the SoftDevice 132 and my bluetooth program. Is there any way to reprogram the NRF52810 over bluetooth rather than using a wired...
