I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
I am using nrf5340 audio DK. After plugging it into the computer, 3 VCOMs and RTT will appear. What are these three ports? docs.nordicsemi.com/.../logging_nrf5340.html Here...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi,
As we know,we can modify the Mesh params though the config model, but when we actually installing and deploying ,If we want to improve the reliability of the Mesh network...
I try to bring an old Project (2017) back to life and use the new SDK 16
the Code usese BLE_GAP_TIMEOUT_SRC_ADVERTISING, but that is removed in the new SDK version,
what...
51822
SDK11
Can we change the advertise interval after 51822 started? I need to change the interval to lower / higher based on the user phone. For example, if its IOS...
How does Broadcast characteristic property of GATT can allow BLE observers devices to read the data without being connected with the device? Does this mean we share data without...
We recently ported to the nRF52832 and our electrical engineer had to make a couple changes from the reference design due to space constraints. The port has worked well during...
Hi! I'm trying to measure the voltage drop across a custom PCB we're developing. This was done while trying to get a clear sense of the current consumption used by our board...
Hi , I am using nrf52832 and try to implement a high throughput in ble5.1. i interface memory with nrf52832 my task is to read the memory and send the data to the app with...
Hey Nordic Team,
I noticed an issue with the SDK and `nrf_serial.c`
After deactivating all legacy code and removing all references to standard UART I noticed that I was...
I need a UARTE driver that does a few things differently to the provided UARTE driver and hence I am writing my own based on nrfx_uarte.c . At the moment I am testing the...
I would like recieve all advertisement in my way, and I development my application on the DK PCA10056. My code as below:
But, I can't recieve any valid advertisement!...
Hi
nRF52833, SDK16
When using a UARTE interrupt I get a fault which I cannot locate, I have the following code:
When my 4 bytes are recieved, i get a fault and the...
Hello,
I'm chasing a bug and narrowed it down to a minimal failing case. Even it's only very few lines, I'm still failing to grasp what's actually happening.
Taking the...
Hey guys,
I'm working with SES, nRF52832 and SDK14.2.0.
I have a timing problem and would like to describe the problem from the beginning.
I have a 1-wire temperature...
Hi.
I'm having Segfault issues with our company's custom boards based on nRF52840 chips.
I do several re-flashing with J-Link EDU Mini Programmer on a daily basis with...
