I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
hi,
i have a timer which is being called each second. when i give timeout less then 1 second then the code executes properly and goes to event handler. but when the timeout...
Can you tell me how to integrate this library so that my code works with it? I'm new to using both these OLEDs and Nordic Semiconductor based devices. THanks
I'm trying to write a firmware for PCA10001, which works like a bootloader. In other words, it can download some data into the Flash. To avoid conflicting with the existed...
Hi thank for reading with your kindness
I used keil with nrfready_desktop_2_/* files
when I clicked "Start/Stop Debug Session" with simulator in debugging session, ...
HI,ALL
i notice that the buttons_leds_init is initiating the bsp function.
just like LED and Buttons.
uint32_t err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS,...
I recently purchased nrf51-DK. I was going through a getting started document which said to update the firmware on the board. After updating it the boards just keep disconnecting...
Hi:
There is a worried question around me.
when i put my product and phone in a firm place after the product connect with APP of phone.
I find that there are lots of...
L.S.
For our products we have chosen to use the RFDigital RFD22301 (previously RFD51822) product which has a nrf81522 chip inside.
Last year we discovered some issues...
What are the S130 SoftDevice v2.0.0-7 alpha iROM and iRAM settings for the nRF51822 and the ble_app_hids_keyboard example?
Someone at Nordic Support suggested the following...
Hii Nordic guys,
I'm trying to test the example project examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay so I just compiled and trying to flash on...
Hello
I am developing an application with BLE and I have just faced to a problem.
I want to check my IDE settings and development environment.
I am using the development...
A good problem to have... we're only seeing 300nA current draw with a 3V lithium primary while in SystemOFF on the nRF51822, using LDO.
Is that correct? We've measured...
HI , ALL
i added a event in the function 'on_ble_evt' like followings:
case BLE_GAP_EVT_ADV_REPORT:
printf("Start Advertising\r\n");
break;
At first i think...
Hi, I mostly use the SDK 7.2 or SDK 10 and S110 7.1 or 8.0
since I have multiple custom boards that uses revision 2 and 3 chips.
My custom board I'm about to use has...
I want get an interrupt from the ADC after every sample (oversampled by 4, so burst is enabled). This works fine with EasyDMA, but I want to be able to not use the EasyDMA...
