I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I've been looking around to find the best way to interface the nRF52 DK with both an LCD screen for printing settings to a panel display, and a rotary encoder, used...
Hi
I don't have the board space for a loop antenna, so I'd like to use a dipole. What sort of RF output / matching stage do I need for this on the nRF905?
Thanks!
Hello
I wrote the program by referring the some examples after compiling the program GPIO pin becomes high immediately (3.3V ) bu my aim is to make the GPIO pin as output...
I have two nrf24l01+ modules communicating on a single channel. The "remote" does 99% of the data transmission while the "base" receives and uploads to a host. Occasionally...
How to use stlink or CMSIS - DAP downloading S110 protocol stack? Jlink can use nrfgostuide down s110 protocol stack, i want to know how to use stlink or CMSIS - DAP download...
Hello,
Is there any information on current consumption for the nRF51822 when running the micro-esb examples? I'm curious as to how much current is being used in a situation...
I'm testing a custom board I did. The board has this 16Mh crystal
geyer-electronic.de/.../GEYER-KX-7_01.pdf
The CL of the crystal is 12 pF. I'm using a pair of capacitors...
Hi,
I am trying to get the ble uart example from the sdk 0.9.2 working on my nrf52 DK board.
But the nRF UART v2.0 application on my android phone, quits instantly after...
Hello,
I'm looking to send a 32 bits word to the example "LebButtonDemo", using an iPhone application created with Evothingd Studio (it uses Javascript).
I'm able to...
Hello
at the moment I have a running S120 BLE firmware update on my nRF51822 hardware.
This works fine on my desk.
But we have the additional requirement to update the...
Hi
I have an custom board which uses an nrf51422 SOC. I am facing issues with my radio.I use an softdevice s110 with an application on it.
The code just works fine with...
Hi Noedic,
I triggered the DFU function through APP, the device restarted and the base service UUID changed from 0x0001(nus function) to 0x1530(dfu function), but it is...
Hello,
I am working on S120 SD v2.1.0 for central and S110 v8.0 SD for peripheral and SDK9.0 and I am able to configure 1 single uuid on central and connect to multiple peripherals...
Hi.
I would like to konw some ditails aboute nRF9E5 device:
What is the rang between 2 devices using 433 mhz.
do you have any samples codes ? i need to trasmitt...
