Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hello,
I am doing some tests with the Heart Rate Service Sample Application for the nRF51822 evaluation board (PCA 10001). Inside the ble_stack_init(), there is this call...
I am trying to bring up a simple program on the IAR tool chain 7.40.1 using an I-Jet debugger using the nRFDK. I have this simple programming running under the Keil code limited...
Hello,
I tried to merge the UART example and the HID keyboard example.
When I pair my phone (android v4.4.4) to my nRF51422 chip (in the phone bluetooth parameters)...
I'm still having a bit of trouble getting my board to receive Heart Rate information from the demo example provided in the 7.2.0 SDK. I've configured the network key correctly...
I am trying to hook up the following accelerometer with my MPU-3050, but I am having trouble reading from the registers. So far I have code that looks like this.
Accelerometer...
Is it possible on the nRF51822 to surface an every from the Soft Device whenever a client attempt a scan (is it SCAN_REQ?)
This is for an iBeacon implementation where I...
I'm doing some work with the nRF51822 smart beacon kit. I tried to do an over the air firmware update of the application, but kept getting dfu invalid state (2) errors after...
We've got an application (not using SD or SDK functions) that locks up the nRF51822 and does not reset even though the watchdog is configured and confirmed to work in all...
The release notes for SD 8.0 note "The default behavior is now that the application can use the CPU while the radio is active".
Does this mean that this code is no longer...
Hi,
I am trying to connect the demo board nrf6929 to my demo nrf51822 (PCA10001).
In nrfready_voice_input_module_user_guide I couldn't find any information about updating...
Hi,
I'm using a lightly modified copy of the Multilink central S120 example code. When I get to ble_stack_init() the first thing it does is SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
I found the Ble Serialization here and the example sourcecode within the sdk sources.
It uses uart with 38.400 Baud and hardware handshake (Rtc/Cts).
Is there also example...
Hi,
Looking at the manuals for the S110 and S120 soft devices, I don't see mention of the bootloader in the S120 manual. Does S120 support bootloaders?
I want to make...
Reading the following post:
devzone.nordicsemi.com/.../
made me think that I could use either the nRF51822 or nRF8001 in my design. However, the following post:
devzone...
Hello everyone,
I have had an idea for a cheap homemade programmer for nRF51822. I don't know if it could work, it's just an idea I would like to discuss with you.
I...
