Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
Hi.
I have been investigating how to use GRTC and LFXO for LFCLK with nRF54L15DK. In my goal, I would like to make the Intermittent application with sleep and GRTC that...
I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi,
I need protection against the MITM attack, what should I modify in heart rate example? Actually, I change the characteristics to BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM...
Hi!
I am using nRF51822 evaluation kit and connecting it as a master to a pair of I2C-devices (using twi_hw_master.c). Everything works well, but when I integrated the...
Hi,
I am using the Evaluation Kit, and I have tried to send some data between the Developoment Dongle (PCA10000) to the Evaluation Kit board (PCA10001). As the Development...
Hi,
Are there any reference design for interfacing a nRF51822 with an external sensor for e.g. an accelerometer (STM LIS3DH, AD ADXL362 etc)
Also do we have a profile...
My application would like to receieve notifications at several different times before a radio notification event. Specifically the application needs to receive notification...
Hello,
i have two operation modes:
One or more devices are bonded and advertising mode with whitelist (BLE_GAP_ADV_FP_FILTER_CONNREQ)
A new proximity central device...
Hi all,
From this forum and the examples given in the "sdk" find two approaches to measuring the battery voltage:
using external divider 10M/2.2M+22nF
using integrated...
In the previous discussion you told me to buy Mod nRF-8001 from olimex and i was also very optimist after going through its design that it can easily be connected to Arduino...
I have an application in which I would like to be able to enable and disable the SoftDevice.
But there are peripherals (Application Timers, Two Wire Interface, etc) that...
Hi,
I'm using PCA10001 connect to a sensor chip.I would like to set the register values for sensor chip as SPI master role and I need to switch to slave role to read the...
Hello,
i just want setup 1Tx and 1 RX using NRF24L01+ chips. but i am confused what should be Transmitter side Tx & Rx and what should be in Rx Tx & RX ? in order to use...
Hi,
There were similar questions already anwsered but none of them work for me. So the situation is as follows. When i program the chip though SWD interface the chip probably...
Hi,
Regarding the source found in "Nordic/Source/ble*" etc (downloaded as part of the nrf518xx SDK
[*] How can I find out which revision/release-tag I'm using. Would...
My design may not connect to a client for most of its operational life but will need to be in advertizing mode whenever not connected. I want to specifiy the advertizing interval...
The nRF Utility app for Android does not support the Galaxy Note 3 yet. Probably because the phone has only been released for a few days so far.
Please add support for...
