Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
"Install the Master Control Panel and the nRF51822 Development Dongle (PCA10000)
Download and install the Master Control Panel from our website. Make sure to select...
Hi,
Been using nRF51822 before but on this new design I have an external MCU running the main duties.
I've been reading up a bit on both but would like to get some thoughts...
Hi nordic engineer:
I want to know the right process to delete the bonds when the device connected.
There is a button used for bonding. When it pressing by more than...
That means, that the nRF51822 is always allowed to send, but on it's receiving side, he could slow down the opponent side by using it's Rts line?
I now, I could archive that...
Hi,
I made simple command shell via UART. It works fine when I type commands in terminal by hand. But I run into troubles when BLE chip is fed from MCU that send characters...
When I connect my ble mouse to the PC win8.1 , media button works normal.
When I power off and power on my mouse, it reconnected to win8.1 PC quickly, sensor ,left button...
I'm using the nRFgo motherboard (nRF6310 together with the PCA10004 Cpu board. I'd configured the nRF51822's Uart to 1 MBaud).
Is the RS232 level shifter (which is part of...
It's this will be work?
// Initialize the Bond Manager.
bond_init_data.flash_page_num_bond = FLASH_PAGE_BOND;
bond_init_data.flash_page_num_sys_attr = FLASH_PAGE_SYS_ATTR;...
Hello：
I need to ask you after the next programmed into how this routine testing 。（nrf51_sdk_v4_4_2_3355\nrf51822\Board\nrf6310\ble\ble_app_alert_notification ） The iphone...
Dear Developer Zone,
I am working with nRF51822 and IOS.
My device can only be connected to one central, so to one iPhone. To refuse connection from others centrals...
Hi all,
I've got some questions about the DFU OTA Nordic example (nRFToolbox):
What is available full stack update or profile update?
Firmware flow, does it need to...
Hi Folks,
I'm running into a problem with the pipes on my nRF8001. After I issue a Connect (0x0F) command, I receive:
CommandResponseEvent (0x84)
ConnectedEvent...
We have setup the RX and TX modes for ANT+ in Advanced Burst mode.
The setter function works (can confirm that by using sd_ant_adv_burst_config_set());
However when...
Hello,
I understand that S310 stack currently supports Ant+ and BLE peripheral. Is there any way to incorporate BLE central (S120) and Ant+ (S210) stacks on the same device...
