Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hello,
Does anybody know what I could be doing wrong either on peripheral or PC when my program on PC reports this error?
I am in the process of writing an application...
Good morning. Thanks for reading. I am brand new to development on Nordic platform but fairly experienced with ARM Cortex, GCC, IAR, Eclipse, etc.
I have a the PCA10003...
Hey guys. I'm very new to Bluetooth 4.0 (actually Bluetooth in general), but I'm hoping to be able to use a Fujitsu MBH7BLZ02-109004 module with an nRF51822 in a product I...
I am attempting to measure battery voltage through the ADC, but am getting inaccurate results. In my setup, I have a 4.2 V battery divided down to the bandgap range using...
HI all:
I am using the nrf24le1.And i confuse about the recive and transmission address in rf transceiver.
What do we use the address to do usually.It will be wonderful...
Copy nrf51.cdb to "C:\Keil\UV4"
Copy nrf51xxx.flm to "C:\Keil\ARM\Flash"
Set the keil project-device to nRF51822(data base : Nordic nRF Series Devices)
This is...
Hi
Is there a documentation of the nRF51822 sniffer interface? e.g. communication structure, command format, captured messages structure etc?
Thanks
Yaron
I'm trying to set up a network where 1 - 4 BLE devices wirelessly talk to a computer. I'm using an arduino connected to the BLE shield.
The computer is a Winows 7 laptop...
Hi,
I'm creating a project on nRF51822 chip and I have a problem with disconnection. In my program I want to disconnect with master after some time e.g. 30 seconds. I'm using...
I'm unable to write my application code to the flash of an NRF51922 (QFAACAA). NRF Studio will let me flash the hex file but it fails verification. If I try programming in...
I have a question, can nRF51822 operate in regular Bluetooth mode like a Bluetooth 2.1 device?
If answer is no then, is there any product from Nordic that operate as Classic...
Hi developers,
I've finally got the nrf51822 working and advertising a good signal to the dongle. :)
After doing all the steps in the NAN-36 pdf-file I hoped that pressing...
Hi all,
I'm using Timer2 while having the SD enabled, and I'm having some problems. I don't seem to be able to reliably set the periodicity of the timer. No matter what I...
I've spent quite a while getting Eclipse on Mac OSX working. I started with the original makefile but have come up with, finally, a working native Eclipse build which does...
Hi all,
I have an external dongle (Bluegiga) that is scanning for BLE devices.
My problem is this: all the BLE devices in my room are showed correctly except my nRF51822...
