Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
In my project,I want to send commands when BLE is connecting to read datas in the nrf51822 internal flash which were writen into the flash previously , but I found the ble_flash_page_read...
Hi,
I have pca100000 v 1.0 and v 2.1.0, and the master control panel application with the latest version of 3.5.0. The firmware we have flashed on both the dongle is 0.9...
Hi,
How can i run the nRF utility application using my Nexus 4 smartphone? After installing the application it is showing that device is not supported.
Regards,
Bala...
Hi,
For power critical application, i know that ,we need to enable the peripherals whenever we need that.
After we need to disable by using ENABLE register.
My question...
i'm testing in my pcb. i designed a nrf24le1f board (the guidance of the datasheet). But i transmitted not far, about 2-10cm a long. I don't know i wrong in design pcb or...
I have the nRF Loader app installed on an iPad Mini. I have the dfu_dual_bank_ble firmware from SDK V5.0.0 and SoftDevice V6.0.0.1-beta loaded on my nRF51822.
The app is...
Hi all,
I am in the process of debugging the ANT broadcast_tx example program using Keil on nRF51422.
I have flashed the program on nRF51422.
After entering the debugging...
I have nRF51822-EK
I am not sure whats going on with it.
I can run LED blinky example nicely ( no surprise :D )
But when I try to run softdevice examples like heart...
I have used TI Code composer which is based on Eclipse, and they created a specific Target menu option which allows resets and other target specific items.
Is there a CDT...
Hi,
I use the UART to do the device firmware update and have used the dfu_dual_bank_hcl to compile.I use the nRFgo Studio V1.16
to program the s110_nrf51822_5.2.1_softdevice...
I've downloaded the latest SDK and soft device. I've been able to compile the ble_app_ancs project, run it on my dev board and even connect to my iPhone. Although I'm getting...
Hi everyone
I'm using the nrf51822 connect with stm32f103 through UART,it's current is >1.9mA,is it normal?
I have full reset to disable the debug interface,it can...
Hello developers,
I've got an nrf51822 EVA kit with on it the QFAACA chip. KEIL v5.0.5, J-link V4.78, nRFGo Studio V1.16 and nrfGo SDK (zip) V4.4.2. The Softdevice on the...
when I enter the system off mode then used a GPIO to wake up the IC, the "RESETREAS" register show "Reset due to wake-up from OFF mode when wakeup is triggered from the
DETECT...
