I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
Hi All.
I am trying to measure the consumption of the SoCs inside the nRF52840DK and the nRF52833DK using a PPK(II), both running the same code to make comparisons.
First...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
Testing with NCS 3.0.1 and nRF54L15-DK. I would like my devices to be able to work as channel sounding initiator as well as reflector role. In my own code I have integrated...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
